Port of flash_cc2531 to FreeBSD. This is likely more just include a wiringPi compatible library for FreeBSD. Any new files are BSD licensed and NOT GPLv3 license.
Nevar pievienot vairāk kā 25 tēmas Tēmai ir jāsākas ar burtu vai ciparu, tā var saturēt domu zīmes ('-') un var būt līdz 35 simboliem gara.
 
 
 
John-Mark Gurney 1725f515f5 ignore various build artifacts.. pirms 3 gadiem
.gitignore ignore various build artifacts.. pirms 3 gadiem
CCDebugger.c minor comments about the delay.. pirms 3 gadiem
CCDebugger.h suppress some compilation warnings. pirms 3 gadiem
LICENSE Initial commit pirms 5 gadiem
Makefile make it compile on FreeBSD pirms 3 gadiem
README.md Update README.md pirms 3 gadiem
cc_chipid.c increased default delays for better stability. pirms 4 gadiem
cc_erase.c increased default delays for better stability. pirms 4 gadiem
cc_read.c fix up so that it compiles w/o warnings.. pirms 3 gadiem
cc_write.c fix up so that it compiles w/o warnings.. pirms 3 gadiem
wiringPi.c add the wiringPi wrapper functions for FreeBSD.. pirms 3 gadiem
wiringPi.h add the wiringPi wrapper functions for FreeBSD.. pirms 3 gadiem

README.md

flash_cc2531

flash CC2531 USB dongle from your Raspberry, without Arduino nor CC Debugger.

prerequisites

You need a Raspberry or an Odroid-c2.
WiringPi must be installed (if it is not preinstalled, you can usually install it with sudo apt-install install wiringpi).
I have designed flash_cc2531 on a Raspberry Pi 3 with raspbian, but successful flashes have been reported on pi 1 and pi 2 : see sections use other pins and what to try if it doesn’t work.

Getting Started

Download flash_cc2531 on your raspberry:

git clone https://github.com/jmichault/flash_cc2531.git

Connect the following pins of the debug port to the GPIO port :

  1. pin 1 (GND) --> pin 39 (GND)
  2. pin 7 (reset) --> pin 35 (wPi 24, BCM19)
  3. pin 3 (DC) --> pin 36 (wPi 27, BCM16)
  4. pin 4 (DD) --> pin 38 (wPi 28, BCM20)

and insert the usb dongle in a port.

A downloader cable CC and 4 Dupont line Female to Female are perfect for this purpose :

test by running :

cd flash_cc2531
./cc_chipid

it should return :

  ID = b524.

If you see 0000 or ffff, something is wrong and you should probably check your wiring.

Usage

To save the content of the flash to save.hex file :

./cc_read save.hex

(takes around 1 minute).

To erase the flash :

./cc_erase

Note : You must erase before writing.

To flash file to cc2531 :

./cc_write CC2531ZNP-Prod.hex

(takes around 3 minutes).

Use other pins

all commands accept following arguments :

        -c pin : change pin_DC (default 27)
	-d pin : change pin_DD (default 28)
	-r pin : change reset pin (default 24)
  	-m : change multiplier for time delay (default auto)

the pin numbering used is that of wiringPi. Use “gpio readall” to have the layout on your pi (wPi column).

example, if you want to use pins 3, 11 and 13 : Connect the following pins of the debug port to the GPIO port :

  1. pin 1 (GND) --> pin 14 (GND)
  2. pin 7 (reset) --> pin 3 (wPi 8, BCM2)
  3. pin 3 (DC) --> pin 11 (wPi 0, BCM17)
  4. pin 4 (DD) --> pin 13 (wPi 2, BCM27)

and now you can read chip id, save flash content, erase flash, and write flash with following commands :

./cc_chipid -r 8 -c 0 -d 2
./cc_read -r 8 -c 0 -d 2 save.hex
./cc_erase -r 8 -c 0 -d 2
./cc_write -r 8 -c 0 -d 2 CC2531ZNP-Prod.hex

You can also change default values in CCDebugger.h and recompile executables with make.

what to try if it doesn’t work?

  1. stop all other programs before flash.
  2. fix the cpu speed before flash. Example :
sudo bash
echo performance >/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
exit
  1. use the -m option to increase time delays used. Example :
./cc_write -m 300 CC2531ZNP-Prod.hex
  1. executables are compiled on my raspbian distribution, you can try to recompile for your distribution with make.

License

This project is licensed under the GPL v3 license (see COPYING).