U-Boot SPL 2018.03 (Jul 09 2018 - 05:43:09 +0000)
DRAM: 2048 MiB
Trying to boot from MMC1


U-Boot 2018.03 (Jul 09 2018 - 05:43:09 +0000) Allwinner Technology

CPU:   Allwinner A64 (SUN50I)
Model: Pine64+
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
Loading Environment from FAT... Card did not respond to voltage select!
** Bad device mmc 1 **
Failed (-5)
Loading Environment from MMC... Card did not respond to voltage select!
*** Warning - MMC init failed, using default environment

Failed (-5)
In:    serial
Out:   serial
Err:   serial
Net:   phy interface7
eth0: ethernet@01c30000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found EFI removable media binary efi/boot/bootaa64.efi
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disks on usb...
Disk usb0 not ready
Disk usb1 not ready
Disk usb2 not ready
Disk usb3 not ready
Scanning disks on mmc...
Card did not respond to voltage select!
MMC Device 2 not found
MMC Device 3 not found
Found 3 disks
423456 bytes read in 51 ms (7.9 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
## Starting EFI application at 40080000 ...
Consoles: EFI console  
Command line arguments: loader.efi
Image base: 0x40080000
EFI version: 2.70
EFI Firmware: Das U-Boot (rev 0.00)

FreeBSD/arm64 EFI loader, Revision 1.1
(Mon Jul  9 19:08:05 UTC 2018 root@releng3.nyi.freebsd.org)
   Load Path: /\efi\boot\bootaa64.efi
   Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/USB(0x6,0x0)/HD(1,0x01,0,0x81f,0x1afa6)
   BootCurrent: 0000
   BootOrder: 0008 0000[*] 0000[*] 0000[*] b740 b9f2 0000[*] 0000[*] 1b3c bdf8 0000[*] 0000[*] b7a0 b9f2 0000[*] 0000[*] 1e60 bdf8 0000[*] 0000[*] 7e58 b9f3 0000[*] 0000[*] f750 b9f6 0000[*] 0000[*] c000 bdfc 0000[*] 0000[*] 8000 bdfb 0000[*] 0000[*] a86e bdfa 0000[*] 0000[*] 4e20 0000[*] 0000[*] 0000[*] b7d0 b9f2 0000[*] 0000[*] 502c bdf9 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0004 0000[*] 0000[*] 0000[*] 8ea8 bdfb 0000[*] 0000[*] b838 b9f2 0000[*] 0000[*] b258 bdf8 0000[*] 0000[*] 7e50 b9f3 0000[*] 0000[*] f7d0 b9f6 0000[*] 0000[*] b9a8 b9f2 0000[*] 0000[*] b8e0 b9f2 0000[*] 0000[*] b3b4 bdf8 0000[*] 0000[*] 8ea8 bdfb 0000[*] 0000[*] b000 b8eb 0000[*] 0000[*]
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/USB(0x6,0x0)/HD(1,0x01,0,0x81f,0x1afa6)
Setting currdev to disk0p1:
And now the part: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/USB(0x6,0x0)/HD(1,0x01,0,0x81f,0x1afa6)
Setting currdev to disk0p1:
And now the part: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/USB(0x6,0x0)/HD(2,0x01,0,0x1b7c5,0x1d9083b)
Setting currdev to disk0p2:
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x8d3ad5 data=0x14a520+0x7cd4ac syms=[0x8+0x120810+0x8+0x113925]
/boot/entropy size=0x1000
/boot/kernel/umodem.ko text=0x2160 text=0x13d0 data=0x102c8+0xfd48 syms=[0x8+0xf18+0x8+0xb62]
efi-autoresizecons: Neither Graphics Output Protocol nor Universal Graphics Adapter present

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               
Using DTB provided by EFI at 0x48000000.
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-ALPHA1 #4 r337599M: Mon Aug 13 13:51:22 UTC 2018
    freebsd@generic:/usr/src/sys/arm64/compile/GENERIC arm64
FreeBSD clang version 6.0.1 (tags/RELEASE_601/final 335540) (based on LLVM 6.0.1)
WARNING: WITNESS option enabled, expect reduced performance.
VT: init without driver.
KLD file umodem.ko is missing dependencies
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
random: entropy device external interface
MAP 48000000 mode 2 pages 4
MAP b8f25000 mode 2 pages 1
MAP bdfbb000 mode 2 pages 1
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
clk_fixed0: <Fixed clock> on ofwbus0
clk_fixed1: <Fixed clock> on ofwbus0
clk_fixed2: <Fixed clock> on ofwbus0
simplebus0: <Flattened device tree simple bus> on ofwbus0
ccu_a64ng0: <Allwinner A64 Clock Control Unit NG> mem 0x1c20000-0x1c203ff on simplebus0
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x1c2b000-0x1c2b3ff irq 21 on simplebus0
iicbus0: <OFW I2C bus> on iichb0
regfix0: <Fixed Regulator> on ofwbus0
ccu_sun8i_r0: <Allwinner SUN8I_R Clock Control Unit NG> mem 0x1f01400-0x1f014ff on simplebus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller> mem 0x1c81000-0x1c81fff,0x1c82000-0x1c83fff,0x1c84000-0x1c85fff,0x1c86000-0x1c87fff irq 23 on simplebus0
gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 224
gpio0: <Allwinner GPIO/Pinmux controller> mem 0x1c20800-0x1c20bff irq 12,13,14 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Allwinner GPIO/Pinmux controller> mem 0x1f02c00-0x1f02fff irq 26 on simplebus0
gpiobus1: <OFW GPIO bus> on gpio1
generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
rtc0: <Allwinner RTC> mem 0x1f00000-0x1f00053 irq 24,25 on simplebus0
rtc0: registered as a time-of-day clock, resolution 1.000000s
awusbphy0: <Allwinner USB PHY> mem 0x1c19400-0x1c19413,0x1c1a800-0x1c1a803,0x1c1b800-0x1c1b803 on simplebus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
aw_mmc0: <Allwinner Integrated MMC/SD controller> mem 0x1c0f000-0x1c0ffff irq 4 on simplebus0
mmc0: <MMC/SD bus> on aw_mmc0
ehci0: <Allwinner Integrated USB 2.0 controller> mem 0x1c1b000-0x1c1b0ff irq 10 on simplebus0
usbus0: EHCI version 1.0
usbus0 on ehci0
ohci0: <Generic OHCI Controller> mem 0x1c1b400-0x1c1b4ff irq 11 on simplebus0
usbus1 on ohci0
gpioc0: <GPIO controller> on gpio0
uart0: <16750 or compatible> mem 0x1c28000-0x1c283ff irq 15 on simplebus0
uart0: console (115384,n,8,1)
iic0: <I2C generic I/O> on iicbus0
gpioc1: <GPIO controller> on gpio1
awg0: <Allwinner Gigabit Ethernet> mem 0x1c30000-0x1c31fff,0x1c00030-0x1c00033 irq 27 on simplebus0
miibus0: <MII bus> on awg0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on miibus0
rgephy0:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy1:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
awg0: Ethernet address: 02:ba:1a:xx:xx:xx
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
usbus1: 12Mbps Full Speed USB v1.0
ugen0.1: <Allwinner EHCI root HUB> at usbus0
uhub0: <Allwinner EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Generic OHCI root HUB> at usbus1
uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
mmcsd0: 16GB <SDHC SC16G 8.0 SN 7C723DFA MFG 04/2018 by 3 SD> at mmc0 50.0MHz/4bit/32768-block
Release APs...done
CPU  0: ARM Cortex-A53 r0p4 affinity:  0
Trying to mount root from ufs:/dev/ufs/rootfs [rw]...
mmc0: ACMD42 failed, RESULT: 4
 Instruction Set Attributes 0 = <AES+PMULL,SHA1,SHA2,CRC32>
mmc0: Card at relative address 43690 failed to set bus width
 Instruction Set Attributes 1 = <>
         Processor Features 0 = <AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32>
         Processor Features 1 = <0>
      Memory Model Features 0 = <4k Granule,64k Granule,MixedEndian,S/NS Mem,16bit ASID,1TB PA>
      Memory Model Features 1 = <>
      Memory Model Features 2 = <32b CCIDX,48b VA>
             Debug Features 0 = <2 CTX Breakpoints,4 Watchpoints,6 Breakpoints,PMUv3,Debug v8>
             Debug Features 1 = <0>
         Auxiliary Features 0 = <0>
         Auxiliary Features 1 = <0>
CPU  1: ARM Cortex-A53 r0p4 affinity:  1
CPU  2: ARM Cortex-A53 r0p4 affinity:  2
CPU  3: ARM Cortex-A53 r0p4 affinity:  3
WARNING: WITNESS option enabled, expect reduced performance.
uhub1: 1 port with 1 removable, self powered
uhub0: 1 port with 1 removable, self powered
Setting hostuuid: 30633239-3130-6162-3161-326466636139.
Setting hostid: 0x1bfe9983.
No suitable dump device was found.
Starting file system checks:
/dev/ufs/rootfs: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ufs/rootfs: clean, 1807783 free (78511 frags, 216159 blocks, 2.1% fragmentation)
Mounting local filesystems:.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib
Setting hostname: generic.
Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED
Feeding entropy: .
lo0: link state changed to UP
awg0: link state changed to DOWN
Starting Network: lo0 awg0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
	options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
	inet6 ::1 prefixlen 128 
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 
	inet 127.0.0.1 netmask 0xff000000 
	groups: lo 
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
awg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=8000b<RXCSUM,TXCSUM,VLAN_MTU,LINKSTATE>
	ether 02:ba:1a:xx:xx:xx
	media: Ethernet autoselect (none)
	status: no carrier
	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
Starting devd.
awg0: link state changed to UP
Starting dhclient.
DHCPREQUEST on awg0 to 255.255.255.255 port 67
ip length 328 disagrees with bytes received 332.
accepting packet with data after udp payload.
DHCPACK from x.x.x.x
bound to x.x.x.x -- renewal in 16479 seconds.
add host 127.0.0.1: gateway lo0 fib 0: route already in table
add host ::1: gateway lo0 fib 0: route already in table
add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
Creating and/or trimming log files.
Starting syslogd.
Clearing /tmp (X related).
Updating motd:.
Mounting late filesystems:.
Performing sanity check on sshd configuration.
Starting sshd.
Starting cron.
Starting background file system checks in 60 seconds.

Mon Aug 13 17:27:20 UTC 2018

FreeBSD/arm64 (generic) (ttyu0)

login: